Low EMF infrared sauna claims, checked

Eleven brand statements about magnetic fields in infrared saunas, set side by side by unit, distance, load and who measured. This page is about how the figures are published. It says nothing about what magnetic fields do to the body, and we have not measured any cabin.

Sources last read 22 Nov 2026How we check

Each dot is a figure a brand publishes, placed at the distance the brand states (log scale up the side). A vertical line joins a published low and high. Figures with no stated distance sit in the lane on the right, because they cannot be placed. The dashed lines are a standard's reference level and one testing firm's own cut-off, from their own documents.
0.1 mG1 mG10 mG100 mG1,000 mG0 in6 in12 in24 in36 in48 inDistance the brand statesNo distancestatedICNIRP 2010 public reference level [14]Vitatech's own 10 mG line [15]

The claim and our verdict

Sellers say: Ultra-low EMF, virtually 0 mG at the bench Our verdict is Overstated.

Brands publish figures at distances that cannot be compared: one at 1, 2 and 3 feet (0.6 to 4.0 mG at 1 ft, 0.4 to 1.8 mG at 2 ft and 0.3 to 0.9 mG at 3 ft), another at the heater surface and the bench, a third with no distance at all. Every figure we found was measured or commissioned by the brand, and no regulation defines "low".

On 22 Nov 2026 we asked a second model to argue against this verdict in both directions. It found a test report we had underused: Sunlighten's own report states a seated torso position, not just "the heater panels". That improves Sunlighten's disclosure, and it is in the table below. The verdict held, because every figure is still measured or commissioned by the brand, at positions that do not line up.

What each brand discloses

Four things decide whether two figures can be compared: the figure and its unit, where it was taken, whether the heaters were on, and who measured. Here is each brand's own wording.

Magnetic field disclosures, quoted from each brand's page or linked report, read 22 Nov 2026
ModelFigureWhereHeatersMeasured by
Sun Home0.3 to 0.9 mGManufacturer pageChecked 22 Nov 2026Sun Home low EMF and safety page, method lineOnly a brand-prepared summary is published; the full Vitatech report VTE-3534 is not linked.Re-check by 22 May 2027Full ledger3 ftwith the heating element under loadVitatech Electromagnetics (commissioned)
Peak Saunas0.178 mGManufacturer pageChecked 22 Nov 2026Peak Saunas sauna safety testing pageHeaters were tested alone inside a magnetically shielded enclosure, not installed in a cabin; the signed report is sent only by email.Re-check by 22 May 2027Full ledger3 incheswhether the heater was on is not statedVitatech Electromagnetics (commissioned)
Plunge6.9 mGManufacturer pageChecked 22 Nov 2026Plunge help center, EMF Levels and Safety InformationIn-house averages with a consumer meter; the article says "individual unit results may vary".Re-check by 22 May 2027Full ledger6 inchesheater condition and frequency band not statedmeasured in-house with a Trifield TF2 meter
JNH Lifestyles0.32 mG RMSManufacturer pageChecked 22 Nov 2026JNH Lifestyles ultra-low EMF/ELF pageApplies to the Ensi and Tosi lines only; no frequency band or report is published.Re-check by 22 May 2027Full ledgeron the heater panel surfaceheater condition not statedVitatech Electromagnetics (commissioned)
Sunlighten, test report0.86 mG RMSTest report, brand commissionedChecked 22 Nov 2026Vitatech Electromagnetics, Sunlighten Sauna EMI Test, VTE-3200 v1.3 (20 January 2021), maximum measurements tableCommissioned by the brand and recorded in its Lenexa warehouse on 5 November 2020; the report describes the readings as taken at the occupant's torso, not at a stated distance in feet.Re-check by 22 May 2027Full ledgerat the seated torso positionheaters under load per the report methodVitatech Electromagnetics (commissioned by Sunlighten)
Sunlighten, web pageunder 1 mGManufacturer pageChecked 22 Nov 2026Sunlighten low EMF pageThe page gives no distance or frequency band; its linked report places the sensor at the seated torso and lists a highest model reading of 0.86 mG RMS.Re-check by 22 May 2027Full ledgerno distance statedheater condition not stated on the pageVitatech Electromagnetics (commissioned)
Clearlight, test report0.0 mGTest report, brand commissionedChecked 22 Nov 2026Vitatech Electromagnetics, Clearlight Infrared Sauna Heater AC ELF EMF Testing and Mitigation Analysis Report (14 September 2016), ConclusionsOne bare 240 V heater hung from a forklift at Vitatech's office, read with a 60 Hz meter (55 to 65 Hz); current Sanctuary and Premier cabins run on 120 V and were not tested in this report.Re-check by 22 May 2027Full ledger3 to 4 ftwith the heater onVitatech Electromagnetics (commissioned)
Clearlight, blogunder 1 mGManufacturer pageChecked 22 Nov 2026Clearlight blog, infrared sauna safety and EMFNo instrument, band or report is given for these figures; the Vitatech report Clearlight links tested one 600 W 240 V heater in 2016, not a cabin.Re-check by 22 May 2027Full ledgerat the heater surfaceheater condition not statedmeasured in-house
Golden Designs3 to 5 mGManufacturer pageChecked 22 Nov 2026Golden Designs, EMF is all around us pageThe page defines tiers, not a test of any model; it gives no distance, instrument or lab.Re-check by 22 May 2027Full ledgerno distance statedheater condition not statedmeasured by not stated
Health Mateno figure on the pageManufacturer pageChecked 22 Nov 2026Health Mate FAQ, What does low EMF mean?The linked 2018 test PDF returned 403 to every fetch, so its figures are not known.Re-check by 22 May 2027Full ledgerno distance statedheater condition not statedlab not named on the page
HigherDOSEno figure publishedManufacturer pageChecked 22 Nov 2026HigherDOSE infrared sauna blanket product page, specificationsA blanket, not a cabin; the page names a charcoal layer "to mitigate EMF and ELF" but gives no measurement.Re-check by 22 May 2027Full ledgerno distance statedheater condition not statedmeasured by not stated

Two patterns stand out. Figures taken at the heater surface or an inch away (JNH, Clearlight's blog, Plunge) cannot be set beside figures taken at the seat (Sun Home at 3 ft, Sunlighten's seated torso). And the only figures with a named outside lab were commissioned by the brand that sells the cabin. Clearlight's linked report tested a single heater, not a cabin, and its meter read 60 Hz (55 to 65 Hz at 3 dB), resolution 0.04 mG in the 0 to 10 mG rangeTest report, brand commissionedChecked 22 Nov 2026Vitatech report for Clearlight (2016), test instruments, FieldStar 1000A narrow band around 60 Hz; the Sunlighten, Sun Home and Peak reports cite 10 to 3,000 Hz, so the figures are not directly comparable.Re-check by 22 May 2027Full ledger.

Where the thresholds come from

Brands quote cut-offs as if they were rules. These are what each one actually is, from its own document:

No regulation we found defines "low EMF" for a sauna. A brand's "ultra-low" is its own label.

What a fair comparison needs

To compare cabins, every figure would need the same five things: a three-axis meter with a stated frequency band, the heaters on and at temperature, the same positions (head, chest and calf at the seat), the same unit (mG RMS), and a lab the brand did not pay. No brand we read meets all five. We have not measured any cabin ourselves; until we do, the honest comparison is the one above: who says what, where.

For the rest of the infrared choice, see Clearlight vs Sunlighten, home saunas ranked on published specs and infrared vs traditional.

AUDIT TRAILBrand pages, test reports and guidelines read for this study19 primary records · Checked 22 Nov 2026
  1. Sun Home: claim wording and how its figure was measured
    Sun Home low EMF and safety page, method line. Manufacturer page. Checked 22 Nov 2026, re-check by 22 May 2027.
    "Independent testing confirms Sun Home Saunas' heating technology operates at ultra-low EMF levels (0.3–0.9 mG at 3 ft). ### Sun Home EMF exposure by distance | Seated distance from heater | Magnetic field range (mG RMS) | Comparison | |---|---|---| | 1 foot | 0.6 – 4.0 mG | Lower than a common kitchen toaster | | 2 feet | 0.4 – 1.8 mG | Near-background levels | | 3 feet (typical position) | 0.3 – 0.9 mG | Virtually background | Values measured in milliGauss (mG). Vitatech considers 10 mG or less to be "Ultra-Low." For context, everyday sources include a toaster (3–70 mG), a hair dryer (60–200 mG), and a cell phone (2–10 mG). **Method:** AC ELF magnetic field, RMS, 10–3,000 Hz, measured with a laboratory-grade fluxgate magnetometer with the heating element under load, across 120V and 230V configurations. Vitatech Electromagnetics, report ref VTE-3534."
    Limit: Only a brand-prepared summary is published; the full Vitatech report VTE-3534 is not linked.
  2. Peak Saunas: published magnetic field figures
    Peak Saunas sauna safety testing page. Manufacturer page. Checked 22 Nov 2026, re-check by 22 May 2027.
    "Yes. Vitatech Electromagnetics measured PEAK heaters at 0.178 mG or less at 3 inches, and under 0.01 mG at 1 foot. Report VTE-3584, November 2026."
    Limit: Heaters were tested alone inside a magnetically shielded enclosure, not installed in a cabin; the signed report is sent only by email.
  3. Plunge infrared sauna: published magnetic field figures
    Plunge help center, EMF Levels and Safety Information. Manufacturer page. Checked 22 Nov 2026, re-check by 22 May 2027.
    "FIR heating panels: Average of 0.74 mG measured at 1 inch from the panel surface, and 0.50 mG at 6 inches. These figures are at or below the typical background EMF level found in the middle of an average home room. Tower heaters: Average of 6.9 mG at 6 inches."
    Limit: In-house averages with a consumer meter; the article says "individual unit results may vary".
    Another source disagrees: "near-zero EMF", no figure. Plunge infrared sauna product page.
  4. JNH Lifestyles: published magnetic field figure
    JNH Lifestyles ultra-low EMF/ELF page. Manufacturer page. Checked 22 Nov 2026, re-check by 22 May 2027.
    "- **EMF/ELF Testing**: A maximum of **0.32 mG RMS** was recorded on the heater panel surface—well below Vitatech’s recommended long-term exposure limit of **10 mG RMS**."
    Limit: Applies to the Ensi and Tosi lines only; no frequency band or report is published.
    Another source disagrees: an average of 0.32 mG from the center of the heater, tested by Intertek and Vitatech. JNH Ensi+ 2 person product page.
  5. Vitatech report VTE-3200 for Sunlighten: highest magnetic field by model
    Vitatech Electromagnetics, Sunlighten Sauna EMI Test, VTE-3200 v1.3 (20 January 2021), maximum measurements table. Test report, brand commissioned. Checked 22 Nov 2026, re-check by 22 May 2027.
    " Frequency Range 10 to 3,000 Hz Amplify II 0.11 mG RMS Sauna Model mPulse Believe 0.16 mG RMS mPulse Conquer 0.66 mG RMS Signature IV 0.86 mG RMS Solo 0.57 mG RMS"
    Limit: Commissioned by the brand and recorded in its Lenexa warehouse on 5 November 2020; the report describes the readings as taken at the occupant's torso, not at a stated distance in feet.
  6. Sunlighten: published magnetic field figure and claim wording
    Sunlighten low EMF page. Manufacturer page. Checked 22 Nov 2026, re-check by 22 May 2027.
    "Vitatech’s testing concluded Sunlighten’s heater panels measure less than 1 mG, with some as low as 0.1 mG, which is almost zero!"
    Limit: The page gives no distance or frequency band; its linked report places the sensor at the seated torso and lists a highest model reading of 0.86 mG RMS.
    Another source disagrees: 0.5 mG or less. Same page, a different paragraph.
    Another source disagrees: 0.11 to 0.86 mG RMS by model, 10 to 3,000 Hz. Vitatech report VTE-3200 for Sunlighten (January 2021).
  7. Vitatech report for Clearlight (2016): magnetic field from one heater
    "It was found that at a separation distance of 3-4 feet the magnetic field levels produced by the Clearlight 600 watt 240 volt sauna heater drop to 0.0 mG (below the detection resolution of the FieldStar 1000 Triaxial Gaussmeter)"
    Limit: One bare 240 V heater hung from a forklift at Vitatech's office, read with a 60 Hz meter (55 to 65 Hz); current Sanctuary and Premier cabins run on 120 V and were not tested in this report.
  8. Clearlight: published magnetic field figure and claim wording
    Clearlight blog, infrared sauna safety and EMF. Manufacturer page. Checked 22 Nov 2026, re-check by 22 May 2027.
    "By contrast, high-quality saunas like [Clearlight® infrared saunas](https://infraredsauna.com/shop/saunas/) measure under 1 mG at the heater surface and nearly 0 mG at the bench, which is far below even normal background EMF in many homes."
    Limit: No instrument, band or report is given for these figures; the Vitatech report Clearlight links tested one 600 W 240 V heater in 2016, not a cabin.
    Another source disagrees: under 1 mG with no distance stated, and "virtually 0 mG" when seated. Clearlight True Wave low EMF/ELF page.
  9. Golden Designs (Dynamic and Maxxus): EMF tier wording
    Golden Designs, EMF is all around us page. Manufacturer page. Checked 22 Nov 2026, re-check by 22 May 2027.
    "**Typical EMF Range**: 3 to 5 milligauss (mG)"
    Limit: The page defines tiers, not a test of any model; it gives no distance, instrument or lab.
  10. Health Mate: EMF wording
    Health Mate FAQ, What does low EMF mean?. Manufacturer page. Checked 22 Nov 2026, re-check by 22 May 2027.
    "Fortunately, your Health Mate infrared sauna heaters have been [3rd party tested](https://healthmatesauna.com/wp-content/uploads/2022/03/EMF-health-mate-sauna-2018.pdf) to verify the EMF emitted is at safe levels."
    Limit: The linked 2018 test PDF returned 403 to every fetch, so its figures are not known.
  11. HigherDOSE infrared sauna blanket: EMF wording
    HigherDOSE infrared sauna blanket product page, specifications. Manufacturer page. Checked 22 Nov 2026, re-check by 22 May 2027.
    "Electrical Field: Low EMF"
    Limit: A blanket, not a cabin; the page names a charcoal layer "to mitigate EMF and ELF" but gives no measurement.
  12. Magnetic field figures one brand publishes for its infrared cabins
    Sun Home summary of Vitatech report VTE-3534 (January 2025). Test report, brand commissioned. Checked 22 Nov 2026, re-check by 22 May 2027.
    "| 1 foot | 0.6 – 4.0 mG | Lower than a common kitchen toaster | [...] | 2 feet | 0.4 – 1.8 mG | Near-background levels | [...] | 3 feet (typical position) | 0.3 – 0.9 mG | Virtually background | [...] AC ELF magnetic field, RMS, 10–3,000 Hz, measured with a laboratory-grade fluxgate magnetometer with the heating element under load"
    Limit: The test was commissioned by the brand and is quoted from the brand's summary. Measured as RMS from 10 to 3,000 Hz with heaters under load.
    Another source disagrees: 0.1, 0.5 and under 1 mG, with no distance stated. Sunlighten low EMF page.
  13. Frequency band of the meter used in the 2016 Clearlight heater report
    Vitatech report for Clearlight (2016), test instruments, FieldStar 1000. Test report, brand commissioned. Checked 22 Nov 2026, re-check by 22 May 2027.
    "by Dexsil Corporation. The FieldStar 1000 has a resolution of 0.04 mG in the 0 – 10 mG range, 1% full-scale accuracy to 1000 mG and a frequency response of 60 Hz (55 – 65 Hz @ 3dB). Three orthogonal powdered-iron"
    Limit: A narrow band around 60 Hz; the Sunlighten, Sun Home and Peak reports cite 10 to 3,000 Hz, so the figures are not directly comparable.
  14. ICNIRP 2010 reference level for general public exposure to magnetic flux density at 50 Hz and 60 Hz
    "50 Hz−400 Hz 2.5 ⫻ 102/f 1.6 ⫻ 102 2 ⫻ 10⫺4"
    Limit: The µT and mG figures are our unit conversion of the table value; it is a guideline reference level (unperturbed rms values), not a law in the US or Canada.
  15. What the 10 mG figure brands quote is
    Vitatech report for Clearlight (2016), executive summary. Test report, brand commissioned. Checked 22 Nov 2026, re-check by 22 Nov 2027.
    "Vitatech recommends 10 mG or less for long term human exposure to electromagnetic fields (EMF)."
    Limit: Vitatech's reports trace this figure to option 3 of a 1995 NCRP draft report, which was not adopted as a US standard; Sunlighten's report from Vitatech states there are no North American regulations on maximum exposure.
  16. Vitatech's own classification of magnetic field levels
    Vitatech Electromagnetics, report VTE-3200 for Sunlighten, appendix on AC ELF levels. Test report, brand commissioned. Checked 22 Nov 2026, re-check by 22 Nov 2027.
    "First order of magnitude 1- to 9.9-mG as low, Second order of magnitude 10- to 99-mG as elevated, Third order of magnitude 100- to 999-mG as high,"
    Limit: A testing firm's house scale printed in a brand-commissioned report, not a standard; it has no "ultra-low" band.
    Another source disagrees: 10 mG or less is "ultra-low" per Vitatech. Sunlighten low EMF page.
    Another source disagrees: 10 mG or less is "Ultra-Low" per Vitatech. Sun Home low EMF page.
  17. Building biology guideline bands for AC magnetic fields in sleeping areas (SBM-2015)
    "2 AC MAGNETIC FIELDS (Low Frequency, ELF/VLF) Flux density in nanotesla nT < 20 20-100 100-500 > 500 in milligauss mG < 0.2 0.2-1 1-5 > 5"
    Limit: Precautionary guidelines from a private building biology body for sleeping areas, not a regulation; neither 3 mG nor 10 mG appears as a band edge.
  18. Clearlight: where it says the 3 mG figure comes from
    Clearlight True Wave low EMF/ELF page. Manufacturer page. Checked 22 Nov 2026, re-check by 22 May 2027.
    "The EPA has proposed a safety standard of 3 milligauss (mG). Sweden has set a recommended safety limit of 3 mG."
    Limit: A brand attribution, not a published standard; no EPA or Swedish document stating 3 mG was found or cited.
    Another source disagrees: US Congress / EPA: 200 nT (2 mG), listed as a comparison value. SBM-2015 Building Biology Evaluation Guidelines, small print.
    Another source disagrees: Swedish rule of 2 mG at 1 m, for computer monitors only. JNH Lifestyles, EMF facts vs fears PDF.
  19. One brand's account of the Swedish 2 mG rule
    JNH Lifestyles, EMF facts vs fears PDF. Manufacturer page. Checked 22 Nov 2026, re-check by 22 May 2027.
    "There is a government regulation in Sweden which requires that all video display terminals (VDTs) and Cathode Ray Tube (CRT) video monitors have magnetic fields less than 2 mG at the operator’s position, which is assumed to be 1 meter in front of the screen."
    Limit: A sauna seller's account, citing Iowa State University EHS, not the Swedish text itself.
    Another source disagrees: Sweden has set a recommended safety limit of 3 mG. Clearlight True Wave low EMF/ELF page.